Early Ford V-8 Club Forum

EFV-8 Club Forum / General Ford Discussion / Steering Wheel Needs to Be Sealed ? ? ?

Reply to Discussion | New Discussion << previous || next >>

Posted By Discussion Topic: Steering Wheel Needs to Be Sealed ? ? ? -- page: 1 2     ersatz 09-04-2013 @ 1:57 PM reply profile send p.m. Member Posts: 42 Joined: Jun 2010 The steering wheel on my '46 Ford Pickup gets tacky & grungy feeling in humid weather. It seems like little balls of stuff come off on your hands and is annoying. What can I seal it with and not worry about it being overly slippery? I'd like to be safe and not lose control. supereal 09-04-2013 @ 2:23 PM reply profile send p.m. Senior Posts: 6819 Joined: Oct 2009 Short of replacement, the best remedy is to have the wheel repainted, as it was originally. Steering wheels are made of a steel core covered with hard rubber or plastic. When the painted cover wears away, you get the grunge you mention. Most good auto body shops can apply a color and clear coat that will return the wheel to its original feel. Trying solvents and cleaning products usually make the problem worse. Good vendors sell replacements, but most have to painted before use. I paid over five hundred dollars for a NOS wheel when cracks reappeared in the original, so be sure your wheel isn't cracked before painting. Some have good luck grinding and filling the cracks, but I didn't. Old Henry 09-04-2013 @ 4:35 PM reply profile send p.m. Senior Posts: 738 Joined: Apr 2010 I've repainted my steering wheel several times with spray cans. Sand, fill cracks and holes, sand, prime, paint several coats sanding between, then clear coat several coats sanding between.(The color I wanted was only flat. I'd recommend it anyway as extra wear layers.) Old Henry (The older I get, the better old looks.) supereal 09-04-2013 @ 5:26 PM reply profile send p.m. Senior Posts: 6819 Joined: Oct 2009 You are better than I am at that, OH. The basic problem with resurfacing steering wheels is that the hard rubber shrinks as it ages. This is why it inevitably cracks. For a "driver", I'd try filling and painting. For those who want a better outcome for the most prominent part of the interior, I'd spring for a repro wheel and a professional finish. I've tried both. The pro painting isn't cheap, so chose the base carefully. kubes40 09-04-2013 @ 6:23 PM reply profile send p.m. Senior Posts: 3395 Joined: Oct 2009 Super, Once again you have offered sound advice. I have restored numerous wheels and have had good fortune. Any sign of a crack whatsoever and I "V" it out. I used to use a two part epoxy for to fill these areas but have found that the new fillers designed for plastic bumper covers works very well and is easier to use. It is designed to withstand the flexing on covers that occurs from normal driving as well as heat fluctuations (expanding / contraction). Once I have done the necessary repairs, I clean the wheel VERY thoroughly and apply a self etching / flexible primer. I then top with base acrylic / clear. The paints chosen, having been designed for modern bumpers, etc. will wear for years. The repop wheels for a 46 pickup look nice. It has been my experience with a number of them that NONE fit correctly. The taper is of the correct angle. However, it is obvious whomever produces these knows little about DEPTH. A couple of the wheels were not taper reamed deep enough and required grinding to allow them to go on the shaft far enough. Others were reamed too deep and had to be shimmed so as not to go on the shaft too far. I am not 100% against a repop wheel in a situation as Ersatz has encountered. However, I would strong suggest the wheel be fitted and any necessary modifications to the taper be completed prior to painting. Mike "Kube" Kubarth carson nv 09-04-2013 @ 7:10 PM reply profile send p.m. Member Posts: 19 Joined: Jul 2013 kubes40 is 100% right. I did the same thing with my '40. 2 part bumper repair material for the cracks, Then a good primer and paint. I used 2 stage paint on mine because of the 2 colors. Its easier to mask off and the clear is VERY durable. Any good body shop can do this for you. The cost may vary of course. My wheel had the little grooves all worn away on the cross bars so I had to re-cut them with wire and small files and anything else I could find. Turned out great! See the pic kubes40 09-05-2013 @ 6:28 AM reply profile send p.m. Senior Posts: 3395 Joined: Oct 2009 Hey "Carson". Yep, you got it! I am just finishing a '40 deluxe wheel. Recently did a '40 V8 (std.) wheel. I use a small jewelers file to cut the grooves. TomO 09-05-2013 @ 7:08 AM reply profile send p.m. Senior Posts: 7250 Joined: Oct 2009 I restored my steering wheel twice. The first time I just cut v grooves where the cracks were and filled them with PC7 epoxy. The cracks reappeared in a couple of years. The second time I cut the grooves and drilled holes in the sides of the groove to anchor the filler. I used the flexible filler available at body shop supply houses. I also used a flex additive in the acrylic primer and top coats. This was done in 2004 and my wheel still looks like new. Tom kubes40 09-05-2013 @ 7:40 AM reply profile send p.m. Senior Posts: 3395 Joined: Oct 2009 Hey Tom, That's the stuff, PC7. I could no longer recall the name. I used that stuff for years with fairly good results. Jack Turpin, the famous steering wheel restorer recommended that stuff in his book. Times have changed obviously and new materials have come upon the market. Like you, the modern flex fillers utilized in body shops is the seemingly best way to go at this time. supereal 09-05-2013 @ 2:47 PM reply profile send p.m. Senior Posts: 6819 Joined: Oct 2009 If I was going to attempt to fix cracks before painting, I'd use JB Weld as a filler. That stuff sticks to almost anything. I tried PC7 epoxy without success.

<< previous || next >>

PAGE: 1 2

NOTE: YOU MUST BE A REGISTERED USER AND BE LOGGED IN TO POST (and reply to) messages in this forum. If you are a first time user, please click the CREATE A NEW ACCOUNT in the masthead above to register and Log In. After that, all you do is LOG IN to enjoy using this site.

DISCLAIMER: The V-8 Club does no independent testing of any of the opinions, thoughts or suggestions presented in the website on the Forum, in the Tech Tips section, or any section. A reader should consider the website to be a forum wherein differing solutions to a particular set of circumstances may be discussed. Ultimately, the selection of an item for an individual's vehicle must be based upon the independent study of the vehicle owner in consultation with people in the hobby and restoration experts.

EFV-8 Club Forum Home | Back to Home Page | Contact the Webmaster

Copyright © 2009 - EFV-8.org
Powered by < CF FORUM > v.2.1