Posted By |
Discussion Topic:
Reading the VIN
-- page:
1
2
|
|
42wagon |
03-28-2013 @ 4:32 AM
|
|
|
Senior
Posts: 584
Joined: Oct 2009
|
Max I think the most important part is the serial number itself. If it matches your title you are good to go. The star was put there to keep people from adding to the number and the 18 was an indication that the engine was a V8. On my frame the *18 is very faint and the number is stamped very heavily. Like Henry put the new kid on the line on stamping serial numbers with an old hand looking over his shoulder. The new kid was stamping too lightly so the old hand said "here kid give me that hammer and I'll show you how it is done". Ted
|
Maxthedog1 |
03-27-2013 @ 8:00 PM
|
|
|
Member
Posts: 24
Joined: Nov 2012
|
After cleaning the top of the frame, I can make out the serial number fairly well, except that I cannot locate the STAR 18. It seems to start out with a dash, then the serial number, followed by a star. Is this possible? Or should there always be a STAR 18 at the beginning?
|
Maxthedog1 |
03-18-2013 @ 7:16 PM
|
|
|
Member
Posts: 24
Joined: Nov 2012
|
Fortunately, I do have enough smarts to have required both the title and a bill of sale. Now I just need to get the number on the frame to be readable. Thanks for all the input.
|
supereal |
03-17-2013 @ 10:42 AM
|
|
|
Senior
Posts: 6819
Joined: Oct 2009
|
You just remove the floorboard, or raise it enough to get a clear view of the area around the inspection plate.
|
DEAN333 |
03-17-2013 @ 10:20 AM
|
|
|
Member
Posts: 256
Joined: May 2012
|
Maybe a dumb question, but what is the easiest way to gain access to read the number on the trans? I have a '36 fordoor.
TIM CARLIG
|
wmsteed |
03-17-2013 @ 8:50 AM
|
|
|
Senior
Posts: 613
Joined: Oct 2009
|
You did not state in your original question the status of your paper work on the vehicle in question.. Did you get a title/registration with the car.. At the very least you should have obtained a Bill of Sale with the VIN/Serial number clearly written on the Bill of Sale. As it has been pointed out, the serial number will start with a star 18000000 star... I deal with a lot of "undocumented" old cars which I gather up in several areas of the western U.S., The majority of the time these vehicles do not have current, or past paperwork.. I do my home work before attempting to get the ownership straightened out.. I rely on the info listed in the Standard Catalog of American cars, printing a copy of the page (s) pertaining to the vehicle in question,to backup reputed numbers I have found on the frame/body.. The info listed in the Standard Catalog usually does the trick if the DMV has a question..
Bill 36 5 win delx cpe
|
drkbp |
03-15-2013 @ 12:40 PM
|
|
|
New Member
Posts: 180
Joined: Aug 2010
|
Max, What is on the trans? As suggested, that's usually much easier to read. Ken in Texas
|
CharlieStephens |
03-15-2013 @ 8:12 AM
|
|
|
Senior
Posts: 888
Joined: Oct 2009
|
Ask the Sheriff's Dept. They may want to use acid to raise it. If you do anything make sure it doesn't look like you are trying to change it. The number also should appear two other places on the top of the left frame rail under the body, let's hope they don't ask you to lift it. Charlie Stephens
|
40 Coupe |
03-15-2013 @ 5:27 AM
|
|
|
Senior
Posts: 1674
Joined: Oct 2009
|
Before removing the paint clean the area and place a piece of white paper over the number location. with the side of a pencil rub the pencil over the white paper until there is pencil markings over all the number locations and then remove the paper and try to read the number on the paper. If this fails you may have to remove the paint and rust. The number starts with a five pointed star then the prefix either 54 for a 60HP or 18 for 85HP then a dash followed by six or seven numbers and finally another star. If your Lucky and the cars transmission has never been changed (rare happening) the same number will be stamped on the transmission cast housing just above the inspection cover for the clutch in a flat surface. The transmission number is much easier to read.
|
42wagon |
03-14-2013 @ 5:40 PM
|
|
|
Senior
Posts: 584
Joined: Oct 2009
|
Max Supereal suggested to someone else using a scotchbrite pad. I would also suggest something nonabrasive such as paint remover or lacquer thinner to remove any paint or crud without disturbing the metal. Another thought is to check the top of the transmission housing just above the little inspection door.If the transmission was never changed the original serial number will appear here as well. Ford originally stamped the number on the transmission when the engine was assembled at the Rouge engine plant. It was then transferred to the frame at an assembly plant.
|