Posted By |
Discussion Topic:
Removing Undercoating
-- page:
1
2
|
|
flathead4rd |
02-05-2010 @ 6:19 AM
|
|
|
New Member
Posts: 169
Joined: Oct 2009
|
Yep. Vince is right. Heat gun, scr*per and patience.
|
bigvince |
02-05-2010 @ 12:30 AM
|
|
|
Member
Posts: 60
Joined: Oct 2009
|
Here's the before
|
bigvince |
02-05-2010 @ 12:24 AM
|
|
|
Member
Posts: 60
Joined: Oct 2009
|
Here's an after shot and you can see the other inner fender that hasn't been stripped. Note: this is the original Ford paint underneath the undercoating!
This message was edited by bigvince on 2-5-10 @ 12:31 AM
|
49inthefastlane |
12-31-2009 @ 10:27 AM
|
|
|
Member
Posts: 14
Joined: Nov 2009
|
Vince has it right. The heat gun works great. Also, a car might have really great original paint beneath that under coating. Use a wood or plastic scraper at first to see what is there as a metal putty knife might scrape to bare metal. Worked on my 49.
|
49inthefastlane |
12-31-2009 @ 10:26 AM
|
|
|
Member
Posts: 14
Joined: Nov 2009
|
Vince has it right. The heat gun works great. Also, a car might have really great original paint beneath that under coating. Use a wood or plastic scraper at first to see what is there as a metal putty knife might scrape to bare metal. Worked on my 49.
|
bigvince |
12-28-2009 @ 9:24 AM
|
|
|
Member
Posts: 60
Joined: Oct 2009
|
I had the same problem on my 48 Woodie. Used a heat gun to soften up the undercoating and then scr*pe it off. Spray some mineral spirits or kerosene on the metal and use coarse steel wool to scrub the metal. It's slow but it it's the best way. I've restored four cars and have used the same way to remove undercoating. It works. Vince
This message was edited by bigvince on 2-5-10 @ 12:20 AM
|
FIGS48 |
12-20-2009 @ 8:18 PM
|
|
|
Member
Posts: 7
Joined: Nov 2009
|
Aircraft stripper works to help soften the undercoating ,but you sill haveto do A LOT OF SCRAPING sanding disk on an air grinder works well after most of the undercoat is removed Fig48-
|
51f1 |
12-20-2009 @ 4:32 PM
|
|
|
Senior
Posts: 573
Joined: Oct 2009
|
Eastwood claims they have something that removes undercoating.
Richard
|
ford38v8 |
12-19-2009 @ 11:46 AM
|
|
|
Senior
Posts: 2780
Joined: Oct 2009
|
Moxie, The easiest way to remove undercoating is to remove the car. I agree with Bob, it can be very dangerous. I still bear the scars of dripping burning undercoat that had to be pulled off my skin while still aflame.
Alan
|
supereal |
12-19-2009 @ 9:03 AM
|
|
|
Senior
Posts: 6819
Joined: Oct 2009
|
The words "easy" and "removing undercoating" should never be used in the same sentence! If the substance wasn't sprayed over rust, etc, it is firmly attached to the metal, and will resist all attempts to get it off. We use a heat gun and a sharp scraper when we have to get to the underlying metal. There were two main types of undercoating: rubberized and petroleum based. Both will burn if a flame is applied. Any effective solvents, such as lacquer thinner or acetone, create explosive fumes with greater force than gasoline, and can't be safely used. More than one car has been destroyed trying it, not to mention serious or fatal burns. Many give up trying, and apply a fresh coat to improve the appearance.
|