Posted By |
Discussion Topic:
Why is the starter wire to the starter causing smo
-- page:
1
2
|
|
flatfoot |
07-10-2019 @ 6:00 PM
|
|
|
Member
Posts: 268
Joined: Mar 2011
|
When starting my newly overhauled '37 motor is smoking from the floor starter switch, which is new. It turns over very slow and then picks up but then slow again. It smokes so bad that I stop trying to start it. Good new generator, new starter, new cutout, etc. Has about 300 miles on the overhaul. Help, please.
|
40cpe |
07-10-2019 @ 6:36 PM
|
|
|
Member
Posts: 477
Joined: Jan 2010
|
Sadly, these days "new" doesn't always mean "good". It sounds like maybe the contacts in the switch are faulty. Carefully feel for heat in the connecting terminals and battery cables and in the switch itself. Where you find the heat will be the source of the resistance. I would be interested in knowing where the switch came from.
|
jims33 |
07-10-2019 @ 6:43 PM
|
|
|
Member
Posts: 25
Joined: Dec 2011
|
The problem is most likely the switch itself. The new made ones aren't very good. If you have an old one it might work better. All that is in there is a set of contacts and a bridge that connects them when you step it down. It could be replaced with a solenoid and a starter button. If you take it apart you will see the trouble, the copper buttons will be "fried". A good switch would have silver contacts and heavy copper parts, but that would make them expensive to make.
|
MG |
07-10-2019 @ 8:48 PM
|
|
|
Senior
Posts: 1262
Joined: Nov 2009
|
I assume that your '37 engine is not in a '37 car in that the 1937 Ford did not use a floor stater switch but rather a stater button on the dash. So, what car/truck is your '37 engine mounted in? From what you describe, it sounds as though the cable from the switch to the starter motor is short to ground before it get to the starter motor. I suspect the smoke is from the insulation burning off this cable....
This message was edited by MG on 7-10-19 @ 11:47 PM
|
flatfoot |
07-11-2019 @ 8:36 AM
|
|
|
Member
Posts: 268
Joined: Mar 2011
|
The motor is in a '36 4 dr. I am beginning to believe it is the starter switch. And it is on the floor. But it was working really well before. The foot switch probably bad. Where might be a good place to purchase one. I live in Northern Caifornia, Redding. Maybe C & G Ford? I'm not sure. Thank-you for the information.
|
flatfoot |
07-11-2019 @ 8:43 AM
|
|
|
Member
Posts: 268
Joined: Mar 2011
|
The battery cables are very hot to the battery. The smoke appears to be coming from the starter switch on the floor. Should I replace the cable to the starter from the switch and the switch? Where to buy them I have no thought. Maybe C & G Ford Parts. I live in Redding, Ca. Thanks for your in-put.
|
kirkstad |
07-11-2019 @ 9:34 AM
|
|
|
New Member
Posts: 192
Joined: Jul 2017
|
C&G lists a floor starter switch,part #48-11450 in their catalog page 141. You could call their tech.info.line at 760 871 o445 with any questions you may have.Their parts seem to be of good quality,but remember part suppliers are limited to where they too can get their supplies, unless they can make them themselves .Jims33 is a good suggestion, My 36 was changed to a starter button years ago before I became owner.I did put in a floor switch years ago but never connected it as yet.My starter button was put in the dash,but you could hide it so not to drill any holes.
|
supereal |
07-11-2019 @ 10:37 AM
|
|
|
Senior
Posts: 6819
Joined: Oct 2009
|
Be sure the current draw of the starter hasn't changed. A dragging armature or other internal short could explain the smoke. In that case, and switch will be cooked.
|
flatfoot |
07-11-2019 @ 1:52 PM
|
|
|
Member
Posts: 268
Joined: Mar 2011
|
What or who is Jims33?
|
MG |
07-11-2019 @ 2:06 PM
|
|
|
Senior
Posts: 1262
Joined: Nov 2009
|
He posted above > jims33 7-10-19 @ 6:43 PM "The problem is most likely the switch itself. The new made ones aren't very good. If you have an old one it might work better. All that is in there is a set of contacts and a bridge that connects them when you step it down. It could be replaced with a solenoid and a starter button. If you take it apart you will see the trouble, the copper buttons will be "fried". A good switch would have silver contacts and heavy copper parts, but that would make them expensive to make."
|