Posted By |
Discussion Topic:
Replacement U-joint flange '51 Custom doesn't fit
-- page:
1
2
|
|
jeremyfd |
05-16-2018 @ 1:38 AM
|
|
|
Member
Posts: 9
Joined: May 2018
|
Yes it's the automatic transmission.
|
40cpe |
05-15-2018 @ 7:36 PM
|
|
|
Member
Posts: 472
Joined: Jan 2010
|
Well, I respectfully disagree. That differential yoke did come on '50 models. And it doesn't fit the output of the transmission and has nothing to do with the drive shaft, except the rear u-joint connects to it. Here is a link to one, showing it fits '49-'55. http://shoebox-central.com/1949-1950-1951-1952-1953-1954-1955-ford-rear-axle-differential-yoke
|
sarahcecelia |
05-15-2018 @ 5:21 PM
|
|
|
Senior
Posts: 1183
Joined: Mar 2013
|
The one that I told you I'd sell, is an original 1950 yoke and will fit you trans. out put shaft or pinion shaft. Money back if you decide when you get it you don't want it; you just pay shipping both ways which will probably be $10 or less (Cheapest way priority mail.) Finding one for sale I think would be difficult at best, because whomever has one is going to want to sell the whole driveshaft. I have sources that you can call, but like I said, I seriously don't think they are going to want to "break up" a good driveshaft to sell one of the yokes.
Regards, Steve Lee
|
sarahcecelia |
05-15-2018 @ 5:07 PM
|
|
|
Senior
Posts: 1183
Joined: Mar 2013
|
I don't know about that yoke being used in 1950 cars. I have two (2) 1950's right now, and when I was 18 I had a '50, and none of them had a rear yoke that looked like that one. One of mine that I have now is an early '50 (4 blade fan) and so was the one I had at 18, the other, my Crestliner, is a later '50 ( 3 blade fan.) I built these last two cars I mentioned.My rear yokes look nothing like that one. Strange??
Regards, Steve Lee
|
40cpe |
05-15-2018 @ 2:55 PM
|
|
|
Member
Posts: 472
Joined: Jan 2010
|
That rear yoke is typical of those used by Ford from'49 up through at least the mid-50s.
|
sarahcecelia |
05-15-2018 @ 11:24 AM
|
|
|
Senior
Posts: 1183
Joined: Mar 2013
|
That's a stange one! Standard shift yokes look nothing like that! Is your car Fordamatic transmission?
Regards, Steve Lee
|
jeremyfd |
05-15-2018 @ 3:21 AM
|
|
|
Member
Posts: 9
Joined: May 2018
|
An update, this is the u-joint flange from my '51. It doesn't look stock. Any idea what it is? Measurements: Inside of Pinion Shaft 1 1/4", Outside 1 5/8".
|
jeremyfd |
05-13-2018 @ 11:15 PM
|
|
|
Member
Posts: 9
Joined: May 2018
|
Steve, you're absolutely right about measuring in mm but the problem is the car was having some work done about a 3 hour drive away... and that's where the yoke broke! They sent me the measurements. I make it 1.634" outside diameter on the original. The part I got was from eBay, I paid $35. Thanks again, look forward to getting measurements! regards, Jeremy
|
sarahcecelia |
05-13-2018 @ 7:23 PM
|
|
|
Senior
Posts: 1183
Joined: Mar 2013
|
Yeah, but why are you using millimeters; millimeters weren't used in the USA until the 2000's ? This is an original drive shaft yoke from a 1950 Ford sedan. I have two. One I use for mechanical work and the other?? I'll measure it for you to make you happy, and respond, but it will fit any '49, '50 '51 car and ???What did the new one cost you? I'll give you a "good break" on it when you reply to my thread with the out side diameter.
Regards, Steve Lee
|
jeremyfd |
05-12-2018 @ 12:49 PM
|
|
|
Member
Posts: 9
Joined: May 2018
|
Delighted if it fits! can you confirm measurements are as described by me?
|