Posted By |
Discussion Topic:
40 bussiness/ 40 5window
-- page:
1
2
|
|
thunder road |
07-08-2017 @ 11:57 AM
|
|
|
Member
Posts: 212
Joined: Dec 2016
|
Mike you are right ,I would never go all out and touch the original never rusted floor pan in this coupe. I have to order a new rear shelf board from Lebarron Bonnie, and this will make a big difference. The original board is sun cracked and faded . Domenic
This message was edited by thunder road on 7-8-17 @ 12:11 PM
|
thunder road |
07-08-2017 @ 11:54 AM
|
|
|
Member
Posts: 212
Joined: Dec 2016
|
Hey trjford8, thank you for all the information I really appreciate it. Same goes to Mike and Tom. Domenic
Domenic
|
kubes40 |
07-08-2017 @ 10:50 AM
|
|
|
Senior
Posts: 3406
Joined: Oct 2009
|
Domenic, I vote for returning your car to stock as nearly as possible. To change a coupe in to a business coupe properly requires a lot more effort than simply installing the small auxiliary seats in the rear and replacing the front seat. The biggest hurdles are the huge differences in the floor pans and interior bracing between the two models. In my humble opinion you will devalue the car by attempting such a modification unless you "go all the way" and address all of the necessary issues associated with such a transformation. By the way, a proper front seat for a business coupe, lake a convertible seat, has a small wooden partition on each side of the drive shaft tunnel. Another tell tale item that is distinctive of the proper business coupe seat.
Mike "Kube" Kubarth
|
trjford8 |
07-08-2017 @ 7:47 AM
|
|
|
Senior
Posts: 4218
Joined: Oct 2009
|
The footrests from the tudor seat can easily be removed, so you now have a larger pool of seats to choose from.
|
thunder road |
07-07-2017 @ 6:55 PM
|
|
|
Member
Posts: 212
Joined: Dec 2016
|
Trjford8 thanks for taking the time to clarify my madness, on the 39-40 split bench seat. Now I'm going to be sure to take good detailed pictures of both the 39 and the 40 split bench seat whenever I 'm at a big show like Hershey . This way when, and "if" I go to purchase a 1940 split bench seat I'll know what to look for. I'm hoping the rear footrests are removable and are the only difference when the seat comes out of a 1940 two door sedan, as compared to a 1940 business coupe, as this doubles the amount of available 1940 split bench seats out their that would work. I own a pair of 01A-1940 auxiliary jump seat , opera seats . I have looked in the back of my 1940 "5 window coupe" and the floor is appox. 23 inches from the side of the driveshaft hump to the side, and 20 inches to the coupe seat when it's adjusted about midway . The jump seats would fit,and if I mounted them to a separate piece of 3\4 plywood and placed it under the carpet, I would not have to drill any holes in the cars floor pan, or alter the car in any permanent way. Also I believe the spilt bench seat has a narrower base width, than the coupe seat that's in their now , which may add some more room. I am not thinking about putting people back their , I just think the business coupe interior is more interesting. If I did this I would save the original coupe seat with the car,and it could always be put back to the rear shelf configuration. The car has the original interior in it now and could use to be freshened up. I know all the purists are going to be mad, but at least i'm not thinking about putting Craiger's on it .Also I may decide to just order and install a new rear shelf , from LeBarron Bonnie and call it a day. Domenic Domenic
This message was edited by thunder road on 7-8-17 @ 5:07 AM
|
trjford8 |
07-07-2017 @ 1:38 PM
|
|
|
Senior
Posts: 4218
Joined: Oct 2009
|
thunder road, even after the '39 seat was upholstered like a '40 it still would not look like a '40 seat. There's nothing wrong with using a '39 seat in a '40 as long as you do not anticipate showing the car for points at an Early Ford V-8 meet.
|
42wagon |
07-06-2017 @ 10:59 AM
|
|
|
Senior
Posts: 585
Joined: Oct 2009
|
I just looked at the V-8 Album which may not be the ultimate source. However in 1939 there was only a Standard Coupe 91-77A and a Deluxe Coupe 91-77B . In 1940 the business coupe was added to the line so there was a Standard Coupe 01A-77A a Deluxe Coupe 01A-77B, a Standard Business coupe 01A-67A, and a Deluxe Business coupe 01A-67B. In 1941 it gets more complicated. There were Deluxe Coupes 11A-77A, Super Deluxe Coupes 11A-77B, and Special Coupes 11A-77C. Then there were coupes with jump seats that appear to replace the Business Coupes of 1940. There were Deluxe Coupe w/Jump Seats 11A-67A and Super Deluxe Coupe w/Jumps Seats 11A-67B. Finally a Super Deluxe Sedan Coupe 11A-72 was added. In 1942 it appears that the Coupe w/Jump Seats was dropped from the line. There were Special Coupes 21A-77C, Deluxe Coupes 21A-77A and Super Deluxe Coupes 21A-77B. Then there were the Deluxe Sedan Coupe 21A-72A and the Super Deluxe Sedan Coupe 21A-72B So 42 Guy is correct. There were no Business Coupes or Coupes with jump seats listed for 1942.
|
42guy |
07-05-2017 @ 6:33 PM
|
|
|
New Member
Posts: 108
Joined: Oct 2009
|
My 42 5 widow has a solid or one piece back on the front seat. It has 2 pins at the top that are removed and the back folds down. It has the package tray that extends to the rear of the interior. I was led to understand that Ford did not call them business coupes.
|
thunder road |
07-05-2017 @ 4:31 AM
|
|
|
Member
Posts: 212
Joined: Dec 2016
|
Thanks to both you guys. You never stop learning. The split bench seat in my first 1940 ford coupe a "business coupe " seemed to have the seat adjusting handle nickel plated? If this was so , I believe it was for durability. Anybody have pictures of the 39 and the 40 seat adjusting handles .If someone had a 1939 split bench seat, and took it to Lebaron Bonney and told them to attach the springs to the frame and upholster it just like a 1940, decide weather you wanted the striped broadcloth, or the mohair and lastly had a 1940 adjusting handle, would it then be the same? Domenic Domenic
This message was edited by thunder road on 7-5-17 @ 4:43 AM
|
trjford8 |
07-04-2017 @ 5:58 PM
|
|
|
Senior
Posts: 4218
Joined: Oct 2009
|
The '39 and '40 split back seats are different. They are upholstered entirely different. The 39 seat has the springs as a separate unit from the frame. The springs are upholstered separately from the frame(backrest) and then attached to the backrest which is a solid unit. The 40 seat has the springs attached to the frame as one unit and the backrest is upholstered as one unit. The '39 seat will fit in a '40 and vice versa but they are definitely different. There's also a difference in the seat adjusting levers.
|