Posted By |
Discussion Topic:
1951 F1 trans linkage
-- page:
1
2
|
|
51f1 |
03-23-2011 @ 9:01 AM
|
|
|
Senior
Posts: 573
Joined: Oct 2009
|
The parts catalog I referenced is the official Ford catalog used by Ford dealers and published when the trucks were new (mine is dated January 1952). They are available sometimes on e-bay and from other sources where old Ford parts are sold. There are numerous suppliers of parts for your old truck. If you are not aware of them, let me know, and I will furnish you a list. Or you can search for them over the Internet. Richard
This message was edited by 51f1 on 3-23-11 @ 9:03 AM
|
PeterFord |
03-22-2011 @ 8:09 PM
|
|
|
New Member
Posts: 125
Joined: Jan 2011
|
Richard: I found this catalog at Amazon. I have ordered it. Many thanks Peter
|
PeterFord |
03-22-2011 @ 8:02 PM
|
|
|
New Member
Posts: 125
Joined: Jan 2011
|
Richard: Very helpful input, Richard. Many, many thanks. Where are these parts available? Where is that catalog available? Peter
|
51f1 |
03-19-2011 @ 12:48 PM
|
|
|
Senior
Posts: 573
Joined: Oct 2009
|
The bushing kits, (grommets), that I have bought came with a swaging tool.
Richard
|
supereal |
03-19-2011 @ 11:20 AM
|
|
|
Senior
Posts: 6819
Joined: Oct 2009
|
The grommets for the arms on both ends of the rods must be attached by swedging the casing. You have to devise a tool for that job to get an even crimp of the brass tube.
|
51f1 |
03-18-2011 @ 11:25 PM
|
|
|
Senior
Posts: 573
Joined: Oct 2009
|
The shift arms on the steering column are engaged by a pin in the lower end of the tube that is mounted on top of and runs most of the length of the steering column. When the shift lever is in the 2-3 position, the pin engages the lower arm. In the 1-2 position, it engages the upper arm. An illustration of this assembly is on page 311 of the 48-52 Truck Chassis Parts Catalog. In case you don't have that publication, I have attached the illustration to this post. (Don't be confused by the illustration in the repair manual and in all of the vendor catalogs. It is for a different model.) I suggest that you remove the steering column, take it apart and replace all of the worn parts. I've never done it, but you might be able to replace all of the parts by removing just the shifter tube (7209) on the outside top of the steering column. The four bronze and rubber bushings, referred to as grommets in the correspondence above, go in the ends of the two remote control rods that go from the column to the transmission and in the shift levers on the steering column. They are readily available in kits. Don't forget the wave washer, part no. 351341-S. This is a spring washer that takes up the play in the connections. http://i250.photobucket.com/albums/gg264/rcrispd/SteeringColumnandShiftAssembly.jpg Richard
This message was edited by 51f1 on 3-24-11 @ 2:01 PM
|
PeterFord |
03-18-2011 @ 5:21 PM
|
|
|
New Member
Posts: 125
Joined: Jan 2011
|
thank you supereal. I really appreciate your help. Peter
|
supereal |
03-18-2011 @ 9:30 AM
|
|
|
Senior
Posts: 6819
Joined: Oct 2009
|
As I recall, when you remove the clamp on the column below the shifting arms and remove the rods, the arms can be dropped down and off. The arms slip over the tube, and are engaged when the tube is raised and lowered by the shift lever. If badly worn, replacement arms are available. They are not the same, as one is longer that the other. Second and high is 01A-7302, low and reverse, 01A-7303.
|
PeterFord |
03-17-2011 @ 9:09 PM
|
|
|
New Member
Posts: 125
Joined: Jan 2011
|
are the arms on the column shift rod attached with a pin? A spline, a key-way? Haven't taken it apart yet. The arms coming out of the trans are fine. I drilled them out and tightened them with roller pins.
|
PeterFord |
03-17-2011 @ 9:04 PM
|
|
|
New Member
Posts: 125
Joined: Jan 2011
|
Thank you for your reply. I have replaced the pins in the shifter arms on the trans. Involved drilling them out and installing roller pins. They are tight. It's the shft column and the way the shifter arms attach. That is where the play is. Are they on a spline, or a key-way system ? Also, where are the grommets you refer to?
|