Posted By |
Discussion Topic:
1946 Mercury 4-dr. sedan
-- page:
1
2
|
|
Peder D |
06-24-2010 @ 1:30 PM
|
|
|
Member
Posts: 95
Joined: Oct 2009
|
Clutch chatter has been a topic here previously. I have spent the Winter of 09-10 overhauling engine and tranny, also replaced complete clutch. Engine and trans works fine, but I still have clutch chatter...did I buy a poorly manufactured clutch? What have I overlooked? Thanks, Peder
|
TomO |
06-25-2010 @ 8:39 AM
|
|
|
Senior
Posts: 7250
Joined: Oct 2009
|
You may have a small amount of clutch chatter until you get the clutch release and engine speed coordinated. Motor mounts, rear trans mount, engine speed are all factors in clutch chatter.
Tom
|
Johns46coupe |
06-26-2010 @ 10:47 AM
|
|
|
Member
Posts: 68
Joined: Apr 2010
|
Supereal responded to a question on clutch chatter on May 16, 2010. I found it helpful and pasted his reply in here. Hope that's ok super.?.? The reason you can't find anti-chatter rods in the book i that Ford discontinued them when it was found that they didn't help much, if at all. The chatter is due, mostly, to the configuration of the drive line. The rear axle pushes on the torque tube which, in turn, moves the engine/transmission on the mounts. This also affects the clutch linkage, amplifying the problem. When, in 1949, Ford went to the Hotchkiss system, the chatter that plagued Ford for decades went away. I am attaching info on a brace that has been used to reduce the problem by transferring the "push" to a cross member. Attached FileTransmission brace diagram.jpg (306 Kbytes)
John
|
supereal |
06-26-2010 @ 11:34 AM
|
|
|
Senior
Posts: 6819
Joined: Oct 2009
|
No problem, John. It should be mentioned that completely removing clutch chatter is very rare. The brace helps to keep the drive line from moving forward as power is applied, which is magnified by the clutch linkage. In cases where the chatter is severe, it sometimes helps to put the rear axle on good jackstands, then slightly loosen the bolts that hold the transmission to the engine and while running the engine at a fast idle, engage and release the clutch. Then, retighten the bolts. If there is any mismatch between the clutch disk and the flywheel, this will often correct it. Sometimes the connection between the transmission face and the engine is not parallel, and must be shimmed slightly. Most of us just live with some chatter, and adjust the engine idle and our left leg to ease the clutch from a standstill.
|
37RAGTOPMAN |
06-27-2010 @ 8:36 AM
|
|
|
Senior
Posts: 1958
Joined: Oct 2009
|
I would drive the car and put some miles on it,sometimes the clutch disc face need to be smoothed down,and it has to do with getting used to the pedals and the way you work them, I heard years ago that to reduce the chatter you placed the bumber against a stout tree and released the clutch, slipping a little, this wore the clutch disc just a little,and made contact better.and was flat and even, I would do this as a last resort, I had clutches freeze up from sitting and had to get the car on the road, and push the cluch done in 2nd gear and give it full throttle to break the clutch free,up and down on the throttle with the clutch depressed, do this with no traffic or on a side street, HOPE this helps, and good luck, 37RAGTOPMAN KEEP ON TRUCKIN,,,!!!!!!
This message was edited by 37RAGTOPMAN on 6-27-10 @ 9:36 AM
|
Peder D |
06-27-2010 @ 12:07 PM
|
|
|
Member
Posts: 95
Joined: Oct 2009
|
Thanks to everybody for your replies....the attachment from Johns46coupe did not come through here....is it possible to send that directly to my e-mail: peddan@ebnett.no Thank you! Peder
|
Johns46coupe |
06-27-2010 @ 1:02 PM
|
|
|
Member
Posts: 68
Joined: Apr 2010
|
Sorry about the attachment Peder. Use the search function on this sight and search on Supereal. It will show all of his posts. The one I forwarded was dated May 16, 2010. I would send it again but would probably end up the same. This way you can get it from the source.
John
|
supereal |
06-28-2010 @ 11:39 AM
|
|
|
Senior
Posts: 6819
Joined: Oct 2009
|
Peder: If you don't find it in the archives, I'll look it up and send it. Today, I am at the shop and don't have access for that page on this system.
|
supereal |
07-02-2010 @ 10:16 AM
|
|
|
Senior
Posts: 6819
Joined: Oct 2009
|
Thanks, John. I did send it directly to Peder, including a couple of pix of the brace as it was installed.
|
Peder D |
09-23-2010 @ 3:44 AM
|
|
|
Member
Posts: 95
Joined: Oct 2009
|
Thanks for this good info. New clutch-non adjustable-foreign made? removed since chatter was severe. Same with the old clutch. We believe the 3 arms on the clutch disc are not aligned, thus touching the flywheel one at a time.Also the flywheel looks like it is stained with blue marks-overheated? which would contribute to chatter?We are looking to rebuild my old clutch which is adjustable and take the flywheel out and re-surface it? Your advice 6/26/10 loosening bolts trans to engine will be done. Appreciate your comments here...thanks Peder
|