Posted By |
Discussion Topic:
ring and pinion
-- page:
1
2
|
|
sarahcecelia |
05-09-2018 @ 5:30 PM
|
|
|
Senior
Posts: 1194
Joined: Mar 2013
|
Doesn't a 4:10 rear have 41 teeth on the ring gear and 10 teeth on the pinion and that is an original o'drive rear? How about it Tom? Or whomever??
Regards, Steve Lee
|
Kens 36 |
05-10-2018 @ 8:35 AM
|
|
|
Member
Posts: 352
Joined: Oct 2009
|
Steve, I'm not sure of the tooth count. Yes, 4.10 to 1 was the ratio on overdrive-equipped 1949-1951 Fords. 3.73 was standard with regular 3-speed trans. There were several other ratios for Station Wagons and Fordomatics. If you don't have the 1949-1951 book published by the Club and available on this site's Online Store, you need it. Ken
|
sarahcecelia |
05-10-2018 @ 9:12 AM
|
|
|
Senior
Posts: 1194
Joined: Mar 2013
|
I have a manual, but that doesn't tell the tooth count. You divide the number on the ring gear by the number on the pinion and that answer is 4.10. Overdrive rear.
Regards, Steve Lee
|
sarahcecelia |
05-10-2018 @ 4:00 PM
|
|
|
Senior
Posts: 1194
Joined: Mar 2013
|
Well 41 divided by 10 equals 4.10.
Regards, Steve Lee
|
kubes40 |
05-10-2018 @ 6:36 PM
|
|
|
Senior
Posts: 3421
Joined: Oct 2009
|
The ratio does not necessarily equate to ACTUAL tooth count. A 3:78 has nine teeth on the pinion and 34 on the ring. It's a RATIO. If the 4:10 has 41 teeth on the ring and ten on the pinion, that's coincidence.
Mike "Kube" Kubarth
|
BUCKAWHO |
05-11-2018 @ 4:43 AM
|
|
|
Member
Posts: 96
Joined: Feb 2016
|
Hi...Large numbers of teeth on the ring mean a large diameter gear, which in most cases is not desirable, calling for a huge pumpkin. Most I've heard of have a 37 ring and a 9 pinion, which results in a 4:11 ratio, not 4.10. My '51 has a 4:11 , standard with overdrive, and a rather normal sized differential housing. My Vette has 37 and 11 for a 3:36 ratio. BT
|
sarahcecelia |
05-11-2018 @ 7:53 AM
|
|
|
Senior
Posts: 1194
Joined: Mar 2013
|
34 divided by 8 = 377.7, which is 378
Regards, Steve Lee
|
sarahcecelia |
05-11-2018 @ 8:07 AM
|
|
|
Senior
Posts: 1194
Joined: Mar 2013
|
Something s wrong. I have a NOS ring and pinion in the original Ford box. It has 41 teeth on the ring gear, and 10 on the pinion. Its marked "410 to 1 Overdrive." You can't argue with Ford.
Regards, Steve Lee
|
kubes40 |
05-12-2018 @ 8:12 AM
|
|
|
Senior
Posts: 3421
Joined: Oct 2009
|
quote: 34 divided by 8 = 377.7, which is 378 Regards, Steve Lee Actually 377.7 is 377.7, not 378. And, even by your vastly incorrect calculation, 34 divided by eight is (according to you) 3.777, not 377.7. Regardless, 34 divided by eight, at least the last time I checked, is 4.25. Wow. All I can say is "wow". Mike "Kube" Kubarth
This message was edited by kubes40 on 5-12-18 @ 8:18 AM
|
TomO |
05-12-2018 @ 10:35 AM
|
|
|
Senior
Posts: 7264
Joined: Oct 2009
|
I don't understand the whole point of this post. Steve, you say that you have a ring and pinion in a Ford box and the ring gear has 41 teeth and the pinion has 10 teeth and the box is marked 4.10:1 ratio and then you ask the question of "Doesn't a 4:10 rear have 41 teeth on the ring gear and 10 teeth on the pinion and that is an original o'drive rear?". You believe the box, because you say"Something s wrong. I have a NOS ring and pinion in the original Ford box. It has 41 teeth on the ring gear, and 10 on the pinion. Its marked "410 to 1 Overdrive." You can't argue with Ford." So if you had the answer, why did you ask the question? Did you intend to start an argument? Are you trying to test the knowledge of people on the Forum? Or did you just want to waste some time?
Tom
|