Posted By |
Discussion Topic:
Electric Fan
-- page:
1
2
|
|
bob358rt |
07-03-2013 @ 12:42 PM
|
|
|
Member
Posts: 6
Joined: Mar 2013
|
My 35, 5 window with 49 8RT and 6 volt system leaves no room for the stock radiator fan. Thinking of installing a 6 volt fan from Speedway. Will the 6 volt system support the current draw? Believe the fan draws 8 to 10 amps. Any suggestions on options? I'm even considering converting to a 12 volt system. Thanks!
Rule No. 1 - DO NO HARM!
|
TomO |
07-03-2013 @ 4:43 PM
|
|
|
Senior
Posts: 7256
Joined: Oct 2009
|
That depends upon which generator you are using. The 35 generator only supplies about 17 amps if it has not been modified. The 49-51 generator supplies a max of 35 amps and would not have a problem supporting the fan. You could also wire the fan with a switch to turn it on when idling or in slow traffic or go fancy and use a thermostatic switch to turn it on when the engine is hot.
Tom
|
trjford8 |
07-03-2013 @ 6:06 PM
|
|
|
Senior
Posts: 4219
Joined: Oct 2009
|
In addition to Tom's advice you should wire the fan with a relay to take the load off the switch.
|
40cpe |
07-04-2013 @ 6:17 AM
|
|
|
Member
Posts: 475
Joined: Jan 2010
|
Speedway's site says the fan is 2500 cfm but the spec page doesn't list a current requirement. My memory is that a 12v fan with that output requires about 20 amps. If the 6v fan does pull 2500 cfm, the amp draw is going to be significant. You need the amp draw from speedway to be sure you have the capacity to run it.
|
bob358rt |
07-04-2013 @ 6:29 AM
|
|
|
Member
Posts: 6
Joined: Mar 2013
|
According to VanPelts the generator is a 1942-46 (part #21A-10050). Is this the same amp rating as the 49-51? Thanks!
Rule No. 1 - DO NO HARM!
|
40cpe |
07-04-2013 @ 7:29 AM
|
|
|
Member
Posts: 475
Joined: Jan 2010
|
I have a Motors manual that covers models '35 to '49; it says that the '39 up generators produce a maximum of 30 amps at engine RPMs of 1160 to 1650. It says the part number is 21A-10000
|
flathead4rd |
07-04-2013 @ 7:33 AM
|
|
|
New Member
Posts: 169
Joined: Oct 2009
|
My expierence with an electric fan was this. I put one on my 50. It had been converted to 12 volts with a 12 volt generator. The generator could no keep up with the fan's requirements so had to change over to an alternator. Problem solved.
|
buford8 |
07-04-2013 @ 12:42 PM
|
|
|
Member
Posts: 50
Joined: Oct 2009
|
Hi Bob, a high ouput 6 volt alternator is available for your application from several of the early V8 vendors...it might be more work but I think a 12 volt swap will be cheaper...Good luck.
You mess with me, you mess with the whole trailer park!
|
supereal |
07-04-2013 @ 1:38 PM
|
|
|
Senior
Posts: 6819
Joined: Oct 2009
|
As well noted above, electric fans demand more power than the stock generator can provide, not including the headlights and any other high wattage accessories. When I went to halogen headlights in my stock '47, I had to convert to a 6 volt alternator. If you do that, be sure to get the two wire type, rather than the common one wire variety, and a thermostatic controlled fan relay is required. If you don't have room for a "puller" fan, check to see if a pusher fan, that mounts in front of the radiator, will fit. Adequate fans tend to get expensive as quality goes up.
|
bob358rt |
07-09-2013 @ 8:16 AM
|
|
|
Member
Posts: 6
Joined: Mar 2013
|
What is the differences and advantages between the two wire and the one wire? Thanks for the help!
Rule No. 1 - DO NO HARM!
|