Early Ford V-8 Club Forum

EFV-8 Club Forum / General Ford Discussion / No-start on '42 Engine

Reply to Discussion | New Discussion << previous || next >>

Posted By Discussion Topic: No-start on '42 Engine -- page: 1 2     wrosenkrans 04-06-2011 @ 5:50 AM reply profile send p.m. New Member Posts: 134 Joined: Oct 2010 Supereal - inside of the left front fender is where I found the break in the wire at the bullet connector, sounds like the same spot as your problem. I'll see how it goes and if it becomes problematic I'll try your method. Wayne & Barb '42 Super De Luxe Tudor supereal 04-05-2011 @ 6:49 AM reply profile send p.m. Senior Posts: 6819 Joined: Oct 2009 Wayne: Those bullet connectors made assembly easier, but most of us have chased problems with them since. The horns on my '47 kept failing, and I found that one of the bullets along the inside of the left front fender was the cause, and wouldn't stay together. Now, when we find a problem, we place a sleeve of heat shrink tubing over the wire, solder the bullets together, and shrink the tubing to cover the splice. If the tubing is cut to the right length, the result looks as before. The original connectors were rubber covered, and usually the rubber fell off. The plastic repros look less authentic than the shrink tubing. wrosenkrans 04-05-2011 @ 6:05 AM reply profile send p.m. New Member Posts: 134 Joined: Oct 2010 Added bonus from searching for the fuel pump cover bolt - feeling around under a couple brackets I not only found the bolt, but a stray wire with a bullet connector. Looked a little further and found a similar wire coming off the horns with a female end. Cleaned them up and put the two together and voila, my horn now works. Wonder how long it was disconnected, might have been decades from the amount of crud on each end. Wayne & Barb '42 Super De Luxe Tudor supereal 04-03-2011 @ 5:22 PM reply profile send p.m. Senior Posts: 6819 Joined: Oct 2009 A fuel pump in good condition needs no priming. Crud in the fuel line can keep one of the pump valves off it's seat, preventing the pump from drawing fuel from the tank. If you don't have an inline fuel filter close to the tank, chances are you will have a repeat of the problem. We are finding lots of rusty fuel lines now that alcohol is present in gas. It either, or both, loosens contamination and accelerates internal rust where the copper coating has failed. If you install a filter, be sure to use fuel proof hose secured by worm gear clamps, not the spring clamps that are supplied with the filter. wrosenkrans 04-03-2011 @ 4:40 PM reply profile send p.m. New Member Posts: 134 Joined: Oct 2010 Nope - gas out of the Model T, maybe Model T gas doesn't like V-8s despite both being Fords... Wayne & Barb '42 Super De Luxe Tudor MG 04-03-2011 @ 3:21 PM reply profile send p.m. Senior Posts: 1262 Joined: Nov 2009 wrosenkrans, Tell me you didn't prime it with 2 cycle fuel. :o) This message was edited by MG on 4-3-11 @ 3:54 PM wrosenkrans 04-03-2011 @ 3:16 PM reply profile send p.m. New Member Posts: 134 Joined: Oct 2010 Thanks all for your recommendations. Well, I studied the fuel system section in a 32-41 Service Manual and saw a note about priming the pump. So I went out, took the cover and screen off and filled the bowl with gas. As luck would have it, I bumped the cover off of the fender and spent the next half-hour searching for the top bolt. Cleaned everything off well, put it all back together, and holding my breath hit the starter button. She cranked about 10sec and fired off settling into her usual nice idle. So it does look like I lost the prime. I checked everything over and looked OK, so we went for about an hours ride and she ran flawlessly until just before we got home when I noticed some blue smoke from the exhaust in first and second coming off a stoplight. No change in performance, but do I have a ring going? Wayne & Barb '42 Super De Luxe Tudor Henryat1140 04-03-2011 @ 2:30 PM reply profile send p.m. New Member Posts: 110 Joined: Nov 2009 Suggestion for a good source: You can go to www.Fordbarn.com and look for a gentleman named Kenct. He is very good on fuel systems and has lots of experience on what goes wrong and how to correct it. He rebuilds parts, and usually has items in stock. I am not saying he's the only source, but he has been very helpful for me in the past with advice and assistance. 37RAGTOPMAN 04-03-2011 @ 1:16 PM reply profile send p.m. Senior Posts: 1965 Joined: Oct 2009 Did you try priming the carb with fuel to get it running,? I think you lost your prime.maybe the flex line fitting are letting air in the system, letting the fuel flow back into the tank,flex lines if dried out present a problem, if the lines were clogged you should have experienced slowing up or lack of power, but then again you might sucked up dirt and there is obstruction in the system, I would try priming the carb, if it starts, do a vacunm test on the fuel pump,on the inlet side and a pressure test on the outlet side, sometimes removing the fuel line going to the carb, will start the fuel pump to work, just when doing this becarefull of the spilled gas, also if you need a modern rebuilding kit for the fuel pump, TRY Antique Parts Cellar in MASS, www.then-now.com or call 781-335-8660 also have a rebuilding service, if you do not want to do it, try staying with original parts,they are better then the stuff they make today,and it it came off it will go back on, my 3 cents 37 RAGTOPMAN lets hear how you made out,!!!!!!! 42ford 04-03-2011 @ 11:57 AM reply profile send p.m. New Member Posts: 104 Joined: Oct 2009 Remove the fuel line from the pump and blow air very slow back toward the tank and listen for bubbles. The old lines get a lot of crud and need to be changed. Also the tank gets a lot of rust and that sometimes plugs up the line

<< previous || next >>

PAGE: 1 2

NOTE: YOU MUST BE A REGISTERED USER AND BE LOGGED IN TO POST (and reply to) messages in this forum. If you are a first time user, please click the CREATE A NEW ACCOUNT in the masthead above to register and Log In. After that, all you do is LOG IN to enjoy using this site.

DISCLAIMER: The V-8 Club does no independent testing of any of the opinions, thoughts or suggestions presented in the website on the Forum, in the Tech Tips section, or any section. A reader should consider the website to be a forum wherein differing solutions to a particular set of circumstances may be discussed. Ultimately, the selection of an item for an individual's vehicle must be based upon the independent study of the vehicle owner in consultation with people in the hobby and restoration experts.

EFV-8 Club Forum Home | Back to Home Page | Contact the Webmaster

Copyright © 2009 - EFV-8.org
Powered by < CF FORUM > v.2.1