Posted By |
Discussion Topic:
39 fuel pump rebuild
-- page:
1
2
|
|
parrish |
11-04-2009 @ 3:29 PM
|
|
|
Member
Posts: 349
Joined: Oct 2009
|
The car had not run since 1960, but I was able to coax it into starting up a few weeks ago with a quick manual fuel feed directly into the carb bowl. Since then I've replaced the fuel pump diaphragm and with the pump in my hand I can manually push the lever and create enough of a vacumn at the fuel line inlet to feel air pushing out the outlet leading to the carb. However, when mounted on the fuel pump stand there is no such vacumn. Assuming that the lever was not being pushed up high enough by the fuel pump rod, I looked inside the pump lever cup and it is empty. Is that the probable cause? What should be in that cup? I looked in my catalogs and can't find anything except that one of the pictures of a fuel pump rebuild kit (which costs as much as a new pump!) shows what might be some kind of insert for the cup? Can't tell from the photo...can I substitute something for the cup insert or is a new pump the answer? Thanks!
|
Tom/SC |
11-04-2009 @ 5:17 PM
|
|
|
Member
Posts: 51
Joined: Oct 2009
|
Parrish, there is nothing that goes up inside the cup, except a small dab of grease before installation. I have had very good experience having Ken Igadore to rebuld my fuel pumps for many flathead V8 Fords. His phone number is:1-203-375-9340. Save your self some problems and let him rebuild your fuel pump for you. Tom
|
TomO |
11-05-2009 @ 7:29 AM
|
|
|
Senior
Posts: 7252
Joined: Oct 2009
|
It sounds like you may have too much play in the operating arm of the pump. The arm should start pulling the diaphragm as soon as you start to push up on it.
Tom
|
parrish |
11-05-2009 @ 8:04 AM
|
|
|
Member
Posts: 349
Joined: Oct 2009
|
thanks to both Toms. I always prefer fixing it myself unless specialized tools are needed and are too expensive. I did notice that the vacumn wasn't noticeable until the lever had been pushed quite a ways up, so I'll take the pump apart again and check. I didn't see too many adjustment options the first time through...
|
supereal |
11-05-2009 @ 11:13 AM
|
|
|
Senior
Posts: 6819
Joined: Oct 2009
|
Are you sure that the cup on the pump lever is being seated atop the rod? It is easy to miss the rod when bolting on the pump. I prefer to pull off the pump stand and bolt the pump to it, then put the whole assembly back on the manifold. Put pump rod is at the top of the stroke so you can be sure it is in the cup. Years ago, we used to put small shims we called "pills" in the cup to perk up a weak pump. Today, we replace fuel pumps rather than rebuild them, as the new pumps have "fuel proof" diaphragms and valves. New pumps are about $50, while a repair kit is about half that, making replacement a better deal.
|
TomO |
11-05-2009 @ 1:28 PM
|
|
|
Senior
Posts: 7252
Joined: Oct 2009
|
Parrish, The play comes from worn or poorly manufactured parts. There should be no play in the pivot and when the hook is in the diaphragm, the diaphragm return spring should be compressed enough so that the diaphragm is at the flange area of the lower housing. When you are putting the pump together, start all of the screws and turn them in until the heads just touch the lock washers. Then operate the actuating arm several times, to seat the diaphragm. Tighten the screws by alternating from side to side. Speedway Motors has new pumps for your car and the last one that I bought worked great.
Tom
|
parrish |
11-05-2009 @ 7:15 PM
|
|
|
Member
Posts: 349
Joined: Oct 2009
|
Supereal and Tom: yep, it always seemed easier to remove the pump stand and I'm sure that many stripped pump stand threads are the result of trying to tighten down the pump bolts with the pump lever fighting back! Actually, the one I'm working on has one side stripped and repaired with what appears to be a heli-coil... Anyway, I took the pump off again about an hour ago and started playing Sherlock Holmes with it and here's what I found: with the pump in my hand and the new diaphragm in place , I can push the lever up to hear and feel air coming out the pump outlet (toward the carb). But...when I cover the inlet (coming from fuel line) and push the lever up, I still hear and feel air pushing out from the outlet! So, does that mean one of the valves (check valves?) in the pump body is stuck or is that the normal operation? If it is not normal, then the pump is simply pulling air and that would explain no gas...thanks for the help!
|
TomO |
11-06-2009 @ 7:31 AM
|
|
|
Senior
Posts: 7252
Joined: Oct 2009
|
It is hard to say what your problem is from the information that you have provided. If you have a vacuum gauge, hook it up to the intake of the fuel pump and operate the pump. You should be able to pump 10 inches of vacuum and it should take 1 minute to decay to 0 inches of vacuum. If that works, check the output pressure for 1.5-3lbs of pressure. If you do not have a vacuum gauge, hold your thumb over the intake port and operate the pump arm at least 5 times, then wait a few seconds and remove your thumb from the port. You should feel some vacuum when you remove your thumb from the port. Vacuum leak sources are, top cover gasket, drain plug and input valve.
Tom
|
alanwoodieman |
11-06-2009 @ 7:43 AM
|
|
|
Senior
Posts: 868
Joined: Oct 2009
|
in the old days a piece of shoe leather soaked in oil was inserted in the pump lever cup to help increase the flow and to make up for worn parts.
|
supereal |
11-06-2009 @ 8:03 AM
|
|
|
Senior
Posts: 6819
Joined: Oct 2009
|
Until the pump is primed, and contains fuel, it usually isn't possible to know if there is an internal leak. TomO's suggestion is one way to see if it is working. The other is to pull the fuel line from the carb and put it into a container while you crank the engine. If you pull the spark plugs, it will allow faster pumping, and be easier on the battery. The fact that you found a stripped fastener on the pump stand would seem to show that someone had pump problems in the past. If the new pump doesn't perform, I'd check to see if the pump rod is correct. With an aluminum intake, the length is 7.87". For an iron manifold, 8.87". As you see, it is important that the right rod be used. They look similar, but aren't.
|