Posted By |
Discussion Topic:
Engine power loss
-- page:
1
2
|
|
37RAGTOPMAN |
02-07-2021 @ 11:53 AM
|
|
|
Senior
Posts: 1958
Joined: Oct 2009
|
HI dustbowl I see you found dirt in the bowl of the carburetor, glad you found the problem,. now where did the dirt come from ? what did it look like, you might want to find out, before you have more problems I installed a fuel filter on LS just before the fuel line comes up from the chassis , used a steel fuel filter and made a heat shield , cause I am running duals, this might be a good idea, since you rebuilt the carburetor, to keep it clean my 2 cents 37Ragtopman
This message was edited by 37RAGTOPMAN on 2-9-21 @ 9:15 AM
|
Dustbowl |
02-07-2021 @ 11:34 AM
|
|
|
Member
Posts: 74
Joined: Feb 2011
|
Tom, Max said look for a little debris in the carb, which I found, removed and fixed the problem. Many thanks
|
Mr Rogers |
02-06-2021 @ 6:20 PM
|
|
|
New Member
Posts: 106
Joined: Jul 2019
|
Hmmmmm, going up hill? Wonder it there's sufficient gas in the tank?
|
37RAGTOPMAN |
02-06-2021 @ 10:16 AM
|
|
|
Senior
Posts: 1958
Joined: Oct 2009
|
HI dustbowl HOW old is the gas ? and does it have any water in it ? try a sample in a glass container, just pulling on straws, trying to help. what model carburetor are you using, MODEL 48 ? I assume you have the original ignition system on the car, I assume you checked the needle valve for any dirt, or being some what clogged, did you try running the engine with out air cleaner ? and with a mirror look in the carb and see if you see anything that could cause it running poorly hope this helps, 37Ragtopman
This message was edited by 37RAGTOPMAN on 2-6-21 @ 10:58 AM
|
TomO |
02-06-2021 @ 7:45 AM
|
|
|
Senior
Posts: 7250
Joined: Oct 2009
|
Do you have the stromberg cab on the car? If you do, explain your problem to Uncle Max. He specializes in the Stromberg carbs. http://97-express.com/contact/ Did you run the engine and then take off the top of the carb to check the level? You need to do this to find out if your carb is leaking down or the float level is incorrect. Fuel pump pressure should 2-3psi. Any higher will overcome the float and you will have flooding. You will have to disassemble the fuel pump if the pressure is too high and adjust the return spring pressure. If it is too low, I suggest that you have your fuel pump rebuilt.
Tom
|
51woodie |
02-05-2021 @ 3:50 PM
|
|
|
Senior
Posts: 510
Joined: Jan 2017
|
Could be wrong, but I believe that the fuel pressure should be 2-3 psi.
|
Dustbowl |
02-05-2021 @ 3:30 PM
|
|
|
Member
Posts: 74
Joined: Feb 2011
|
But I will now go out and double check fuel pump out put pressure. I think it should be 5 psi or more.
|
Dustbowl |
02-05-2021 @ 3:28 PM
|
|
|
Member
Posts: 74
Joined: Feb 2011
|
As I explained in my most recent post, I tested flow rate that pump puts out and found it as good or better than Tom suggests. So I don't thing enough fuel getting to my carb is the problem.
|
37RAGTOPMAN |
02-05-2021 @ 2:54 PM
|
|
|
Senior
Posts: 1958
Joined: Oct 2009
|
HI Dustbowl this a long shot, do you have a electric fuel pump ? I assume the gas cap is vented, you could blow out your fuel lines to make sure there is no blockage, front to rear, how old is the front to rear fuel line, has it been replaced when car was restored, and check the fuel pump. remove the top cover to see if you have a build up of dirt I would suspect a fuel problem how is the flex line ? is it fairly new,? this new gas could cause problems with the old flex lines, swelling it up on the inside or maybe it is breaking up leaving particles of small rubber in the fuel lines, this is also true with the fuel pump diaphragm, these also break up , if you have a fuel pump tester see what it tell you, and idf you do not have one, I would take the fuel pump off holding it in my hand with the fuel line attached and work the pump and see if it pumps a steady stream of fuel into a container, maybe you can add some more description let us know so we can solve your problem 37Ragtopman hope this helps check the line from the fuel pump to carb,
|
Dustbowl |
02-05-2021 @ 1:19 PM
|
|
|
Member
Posts: 74
Joined: Feb 2011
|
Well, I thought I had a simple fix with help from both of you. First , with Tom's suggestion, I pulled out the choke (a!! the way) and found that engine went from a little rough (and no power) to smooth and faster. So a gas problem I assumed.. Then I tested fuel flow and found it at least as fast as Tom suggested. Then I took oil the top section of the carb and found the gas level in the carb reservoir to be low when it should have been full. The float adjustment seemed to be correct so I guessed the intake valve was sticking and I replaced it. Expecting success, I then found the engine running rough with no power!!! When the carb was opened, it looked to be clean inside but, of course, I could have a passage blocked. Before I rebuilt the carb, I want to ask you if you can think of anything other than the carb which could be causing my problem I stiil.have a strong spark and the battery is fully charged. I have speculated that ignition timing may have gone bad but that doesn't explain the choke test results. I hate to mess with timing unless I am confident that is source of problem Any suggestions very welcome.
|