Posted By |
Discussion Topic:
Ford Holley carb rebuild
-- page:
1
2
|
|
ford38v8 |
06-04-2010 @ 10:41 AM
|
|
|
Senior
Posts: 2763
Joined: Oct 2009
|
dso72, Your carb marked 59 is correct for Ford/Mercury, 1946-1948.
Alan
|
deluxe40 |
06-04-2010 @ 8:47 AM
|
|
|
Member
Posts: 413
Joined: Oct 2009
|
dso72 - I think the carburetor in the picture is later, maybe '53. It has an automatic choke assembly. By the way, you can probably have some fun identifying the engine block in your car using the following web site: http://www.vanpeltsales.com/FH_web/flathead_specifications.htm
This message was edited by deluxe40 on 6-4-10 @ 8:53 AM
|
dso72 |
06-04-2010 @ 8:40 AM
|
|
|
Member
Posts: 37
Joined: Oct 2009
|
Thanks Alan...I have a 59 cast in the housing.
|
ford38v8 |
06-03-2010 @ 11:27 AM
|
|
|
Senior
Posts: 2763
Joined: Oct 2009
|
dso72, The Ford-Holley 94 you have is an excellent carburetor and will work fine for your '35 Ford, but thought you'd like to know that the Stromberg is the original correct carburetor for a '35. If you're interested in determining the exact model 94 you have, look on the driver's side for a large cast-in code number, such as 91-99; or 59, or several others. Post that number here, and we'll I.D. it for you.
Alan
|
dso72 |
06-03-2010 @ 9:09 AM
|
|
|
Member
Posts: 37
Joined: Oct 2009
|
deluxe40, I'm working on a 35 cabriolet. I purchased the car from the original owner who has had the car stored since the late 50's. The running gear was changed when the owner returned from the war. I believe it is from a 1940 or later Ford. I'm in the process of getting it to run. I'm learning a lot about these old Fords and it has been fun.
|
deluxe40 |
06-02-2010 @ 7:38 PM
|
|
|
Member
Posts: 413
Joined: Oct 2009
|
dso72 - Glad the picture helped. Thanks for getting back to us. What year car are you working on? I'm not sure what car my Holley came off of.
|
dso72 |
06-02-2010 @ 6:58 PM
|
|
|
Member
Posts: 37
Joined: Oct 2009
|
deluxe40 a picture is worth a thousand words! Looking at the picture and reexamining my carb, I had the atomizer bars off by 180 degrees. Corrected the problem and the pieces fit as they should. Thanks for taking the time and helping me with my project.
|
dso72 |
06-02-2010 @ 10:40 AM
|
|
|
Member
Posts: 37
Joined: Oct 2009
|
Thanks Deluxe40 for the reply. I thought the same thing regarding the screws. When the shorter screws are installed (left of pic.), the screws do not reach the threaded holes. In the pic., the longer screws were on the left and the shorter screws on the right with the spray bar. Should I use the longer screws to seat the needle then replace them with the shorter screws? Would this ruin the point of the needle?
|
deluxe40 |
06-02-2010 @ 10:15 AM
|
|
|
Member
Posts: 413
Joined: Oct 2009
|
Here's a picture of an old Holley. Note the plate with shorter screws on the left.
|
deluxe40 |
06-02-2010 @ 9:55 AM
|
|
|
Member
Posts: 413
Joined: Oct 2009
|
There are two hold down plates and two pairs of screws of different lengths. Sounds like you are putting the short screws in place of the longer ones. Look for a pair of similar, but longer, screws. Don't ask how I know.
|